JSPB 3D-Build your own Air-powered Blaster
  • Welcome!
    • Events
    • Authorized manufacturer
    • Gallery >
      • URBAN OPS 1337
      • JSPB PRO2
      • B&B
      • Short novels >
        • The Last Replicant 2054
    • Games >
      • Battle planet
      • 20-Sec Tactical Shooting
      • Zombie Lunch
      • Extra Lives
      • Urban treasure hunter >
        • Coin
    • About
  • CYBERNINJA
    • Build guides
  • Shop
    • Physical
    • Digital
    • Game props
  • Resources
    • Urban OPS
    • Build&Battle
    • JSPB PRO1
    • JSPB PRO2
    • JSPB3D
    • EXTRA LIVES Ver.1
    • ZLIN Rifilig
    • Delta tenonΔ
    • Homemade PETG Spring
    • C5-Launcher Tutorial
    • M-Strike Tutorial
    • B.F.S.G.
    • Applications
    • Troubleshooting
  • [繁中]

SODA MAXXX TROUBLE SHOOTING GUIDE:

12/19/2022

0 Comments

 
1. The lever screw hole is too small to be installed smoothly.
Reason: This is a problem in the manufacturing process, and the new version has eliminated this  issue.
Solution: After locking the screw slightly, use a tool to heat the screw, and then screw in.
槓桿螺絲孔太小,無法順利安裝
原因:這是製造過程上的問題,新版已經排除這個問題.
解法:將螺絲稍微鎖上後,使用工具加熱螺絲,再鎖入.
2. The hole of the hook is too small, difficult to install.
Reason: It is normal for the hole of the hook piece to be tight, so as not to fall off during operation.
Solution: Heat the rivet after inserting it, and press it in hard to expand the hole, so that you can get the proper tightness.
扳機,勾片孔洞太小,困難安裝.
原因:勾片本身緊是正常的,防止運作過程脫落.
解法:將鉚釘插上後加熱,再用力壓入進行擴孔,這樣子可以得到適當的鬆緊度.
3. The trigger cannot be rebounded smoothly.
Reason: the surface is not smooth enough.
Solution: sand the surface and add slicon oil.

Reason: The lever angle needs to be adjusted.
Solution: Adjust the screw on the lever(Fig.3) so that the lever is 90 degrees.
​
扳機無法順利回彈
原因:表面不夠光滑
解法:處理表面,上油

原因:槓桿角度過大
解法:調整槓桿上的螺絲,讓槓桿與blaster呈現90度
Picture
Fig.3
4. Unable to store air.
The trigger rod is too long, resulting in air leakage when it is pressed to the valve,
Reason: This is a subtle difference.
It is designed to be adjusted using the adjusting screw on the lever.​(Fig.3)Total length 6.7cm​
Solution: Use sandpaper to remove the length of 0.1CM from the trigger rod. (Fig.4)
無法儲氣
觸發棒太長,導致觸壓到閥門漏氣.
原因: 這是個細微的差異. 在設計上是可以利用於槓桿上的調節螺絲(Fig.3)進行調整.
解法: 使用砂紙,將去觸發棒除掉0.1CM的長度.​(Fig.4)  總長6.7cm
Picture
Fig.4
5. Pull the trigger, and the darts fly out in one shot.
Use the pump to inflate and pressurize to increase more air pressure,this allows for faster valve bounce times.
扣下扳機 一次噴出所有子彈:
打入更多更多的空氣增加空氣壓力,讓閥門反彈迅速.
6. The pump loosens after a few uses.
Even with the glue applied, we can still reinstall it and get it firm. First remove the screw,
Push the pump hard into the Tee until it stops,finally, we re-attach the glue and lock the screws.
就算塗了膠水,我們仍然可以重新安裝它,達到穩固的效果. 先移除螺絲,
將打氣筒用力推入接頭,直到無法繼續推進,最後我們再重新黏上膠水,鎖上螺絲.
Picture
Picture
0 Comments

    Author

    Ez lin
    Location:
    TAIWAN

    Archives

    January 2023
    December 2022
    July 2022
    February 2022
    November 2021
    October 2021
    September 2021
    August 2021
    July 2021
    June 2021
    May 2021
    April 2021
    February 2021
    November 2020
    October 2020
    September 2020
    August 2020
    May 2020
    April 2020
    March 2020
    February 2020
    January 2020
    December 2019
    October 2019
    September 2019
    August 2019
    July 2019
    May 2019
    April 2019
    March 2019
    February 2019
    January 2019
    December 2018
    November 2018
    October 2018
    September 2018
    August 2018
    June 2018
    May 2018
    April 2018
    March 2018
    January 2018
    December 2017
    November 2017
    October 2017
    September 2017
    August 2017
    May 2017
    April 2017
    February 2017
    January 2017
    December 2016
    November 2016
    October 2016
    September 2016
    August 2016
    July 2016
    June 2016
    May 2016
    March 2016
    February 2016
    January 2016
    November 2015
    October 2015
    September 2015
    August 2015
    July 2015
    June 2015

    Categories

    All

    RSS Feed

LICENSE AGREEMENT
​

Privacy Policy

Refund Policy

If the product has any flaws, please send a message to the webmaster, you can replace the components free of charge.
Picture
Picture
©2003-2020JSPB