JSPB 3D-Build your own Air-powered Blaster
  • Welcome!
    • Events
    • Authorized manufacturer
    • Gallery >
      • URBAN OPS 1337
      • JSPB PRO2
      • B&B
      • Short novels >
        • The Last Replicant 2054
    • Games >
      • Battle planet
      • 20-Sec Tactical Shooting
      • Zombie Lunch
      • Extra Lives
      • Urban treasure hunter >
        • Coin
    • About
  • CYBERNINJA
    • Build guides
  • Shop
    • Physical
    • Digital
    • Game props
  • Resources
    • Urban OPS
    • Build&Battle
    • JSPB PRO1
    • JSPB PRO2
    • JSPB3D
    • EXTRA LIVES Ver.1
    • ZLIN Rifilig
    • Delta tenonΔ
    • Homemade PETG Spring
    • C5-Launcher Tutorial
    • M-Strike Tutorial
    • B.F.S.G.
    • Applications
    • Troubleshooting
  • [繁中]

13-finished

8/20/2020

2 Comments

 
2 Comments

12-Install the barrel

8/20/2020

4 Comments

 
4 Comments

11-check point

8/20/2020

0 Comments

 
1. When inserting darts, you may get your fingers stuck, please use your little finger or pen.
​2. The trigger needs to be pressed hard to the end. After a few times of operation, it will be smoother.
3. The speed of the dart in the test is about 60~70fps,If you feel that the power is insufficient, it is possible that the O-ring of the piston is in the incorrect position, please open and reinstall the O-ring.
4.​ [00:24 ]The trigger is blocked by the trigger guard, please loosen the screws of the trigger guard
0 Comments

10-Combine

8/16/2020

0 Comments

 
0 Comments

09-HEAD

8/16/2020

0 Comments

 
0 Comments

08-PUSH ROD

8/16/2020

1 Comment

 
Picture
1 Comment

07-guide LINE

8/15/2020

2 Comments

 
2 Comments

06-t pull

8/15/2020

1 Comment

 
1. This step requires a little skill, and the installation process requires pressing hard and locking the screws
2. T-PULL screws can be pre-installed halfway.
1 Comment

05-TRIGGER

8/15/2020

1 Comment

 
1. The last screw is to ensure safety to prevent accidental touch.
2. There is a cork on the Push rod ​, we are in this step to make the Push rod ​ track smooth,we will install the cork later.
1 Comment

04-piston

8/15/2020

1 Comment

 
The Rod needs to be pressed to the end.
1 Comment

03-grip

8/7/2020

1 Comment

 
Please protect your eyes and wear goggles.
Be careful with plastic ejection using diagonal pliers
*Tips: 
If the diagonal pliers are not sharp enough to cut off,You can use a lighter to soften the plastic (Bake for 1 second) and then cut it off.
1 Comment

02-core

8/6/2020

1 Comment

 
​Please protect your eyes and wear goggles.
Be careful with plastic ejection using diagonal pliers
Picture
1 Comment

01-SCAR Barrel

8/5/2020

1 Comment

 
​There are two ways to make a barrel

BASIC WAY:

1.​SCAR Barrel-Basic build method without professional tools.
2. ​The tape avoids overlapping.

PRO:

WARNING!
​1. Please use tools carefully to avoid injury. (You can also find suitable tools)
2. Do not cut too deep to avoid cracking.
3. The video has changed speed, please follow your own speed

​---------------------------------------------------------------------------------------------------->>>

Read More
1 Comment

00-Preparation

8/1/2020

0 Comments

 
Difficulty levels: ★★★☆☆
Time required: 3 ~4 HR
​​1. Safety first​
Please wear protective goggles and pay attention to the reminders in the manual.
2. DIY-kit list:
Picture
3. Tool list:
Necessary:
Picture
​Professional tools:
Picture
1. Shockless Hammer
2. Convenient to use in narrow places
3. Maintenance, replacement of cork used
4. Save you a lot of time*
​5. Ratchet [10]*
6. Use Pipe cutter to make scar barrel, the blade should not be too thick.
7. Sand,Used to reduce noise
8. Lighter,Soften 3d printed parts.
9. Carving knife to remove surface bumps
​10. Flashlight

DOWNLOAD MANUAL- PDF

jspb_cyberninja_manual_v1.3.pdf
File Size: 6444 kb
File Type: pdf
Download File

jspb_cyberninja_manual_v1.2.pdf
File Size: 24903 kb
File Type: pdf
Download File

0 Comments

    Author

    Z-LIN
    If you have any questions, please comment below.
    (Please click on the title to enter)
    ​

    Show this page
    on your phone:

    Picture

    Archives

    June 2021
    February 2021
    November 2020
    October 2020
    August 2020

    Categories

    All

    RSS Feed

LICENSE AGREEMENT
​

Privacy Policy

Refund Policy

If the product has any flaws, please send a message to the webmaster, you can replace the components free of charge.
Picture
Picture
©2003-2020JSPB
  • Welcome!
    • Events
    • Authorized manufacturer
    • Gallery >
      • URBAN OPS 1337
      • JSPB PRO2
      • B&B
      • Short novels >
        • The Last Replicant 2054
    • Games >
      • Battle planet
      • 20-Sec Tactical Shooting
      • Zombie Lunch
      • Extra Lives
      • Urban treasure hunter >
        • Coin
    • About
  • CYBERNINJA
    • Build guides
  • Shop
    • Physical
    • Digital
    • Game props
  • Resources
    • Urban OPS
    • Build&Battle
    • JSPB PRO1
    • JSPB PRO2
    • JSPB3D
    • EXTRA LIVES Ver.1
    • ZLIN Rifilig
    • Delta tenonΔ
    • Homemade PETG Spring
    • C5-Launcher Tutorial
    • M-Strike Tutorial
    • B.F.S.G.
    • Applications
    • Troubleshooting
  • [繁中]