JSPB 3D-Build your own Air-powered Blaster
  • Welcome!
    • Events
    • Authorized manufacturer
    • Gallery >
      • URBAN OPS 1337
      • JSPB PRO2
      • B&B
      • Short novels >
        • The Last Replicant 2054
    • Games >
      • Battle planet
      • 20-Sec Tactical Shooting
      • Zombie Lunch
      • Extra Lives
      • Urban treasure hunter >
        • Coin
    • About
  • CYBERNINJA
    • Build guides
  • Shop
    • Physical
    • Digital
    • Game props
  • Resources
    • Urban OPS
    • Build&Battle
    • JSPB PRO1
    • JSPB PRO2
    • JSPB3D
    • EXTRA LIVES Ver.1
    • ZLIN Rifilig
    • Delta tenonΔ
    • Homemade PETG Spring
    • C5-Launcher Tutorial
    • M-Strike Tutorial
    • B.F.S.G.
    • Applications
    • Troubleshooting
  • [繁中]

urban ops Difficult to catch, or pull the trigger

8/29/2018

0 Comments

 
Trigger and Catch mechanism update,If your JSPB Urban ops is working properly, no changes are needed.
​Updated in two ways:
1. You can use sandpaper to grind, as the figure.
2. Download new STL file.
Picture
uo_catch8.stl
File Size: 23 kb
File Type: stl
Download File

uo_trigger6.stl
File Size: 32 kb
File Type: stl
Download File

0 Comments

jspb pro2 ls -Check internal

6/19/2018

0 Comments

 
0 Comments

Trigger can not rebound

11/27/2017

0 Comments

 
Picture
扳機無法回彈可用下列幾個方式排除:
1. ABS棒需上更多矽由
2.將Check valve打開,並將彈簧擴張
​
The trigger can not be rebounded in the following ways to exclude:
1. ABS rods need more silicon grease
2. Open the Check valve and expand the spring
Picture
0 Comments

Can not pump into the air

11/7/2017

0 Comments

 
Picture
The reason the air can not be pump in to tank is that OPV O-ring friction causes pup-up. The solution is to open the OPV and lubricate more in the active area.

無法打入空氣的其中一個原因是OPV運作的時候,O-Ring摩擦導致外翻,解決辦法是打開OPV,並在活動區域上更多的潤滑.

0 Comments

air seal at the pump connector

9/24/2017

0 Comments

 
將打氣筒連結處提升氣密至100%
使用鐵氟龍止水帶提升氣打氣的氣密程度,增加效率!
打氣筒與Air tank的連接處提升氣密的方式為使用鐵氟龍止水帶來密封.
0 Comments

JSPB B&B-FAQ

7/1/2017

0 Comments

 
Q: 扣下扳機有氣體跑出但無法發射子彈.
A: 核心組件內壁有細小凸起物,這是製成的問題,利用甘皮刀(V型刀)移除掉小凸點,子彈將可以滑順通過.
Picture
Picture
Q:扳機小螺絲非常困難鎖入.
A:利用斜角卡住(Fig2),並且鎖入,操作時請注意手部安全.
Picture
(Fig2)
Q: 扣下扳機順利發射後,扳機無法彈回.
A: 請在扳機上矽油(Fig2)
0 Comments

JSPB Pro2 FAQ

7/1/2017

0 Comments

 
Q: 透過測試氣密是正常的,但組裝完成後,扣下扳機沒有釋放氣體.
A: 鬆開班機上的螺絲,延長扳機觸發桿子的長度,注意不可以一次放太長,會把氣閥頂壞.
Q: 扣下扳機後射出的子彈力量相當弱,填裝子彈的時候很緊,不好填裝.
A: 槍管13cm與彈倉13.3cm的管子安裝顛倒,內壁比較粗的是槍管.
Q: 打氣筒灌了幾下後就彈出來,無法順利把空氣灌入
A: OPV內的彈簧鬆動去按壓到單向氣閥導致,修改彈簧可以讓它運作更好!
Picture
Q: 螺絲孔鬆動了怎麼辦?
A: 利用A4的紙塞入,即可有固定作用
0 Comments

EXTRA LIVE FOR CQB- FAQ

6/30/2017

0 Comments

 
Q: ABS棍棒無法塞入孔洞
A: 方法一利用熱漲冷縮原理,ABS棒冷凍後即可插入
方法二使用4.0的鑽頭開一個更大的洞
Q: ABS棒鬆動
​A: 使用雙面膠帶於棒子上,再塞入洞即可穩固
Q:安裝氣球的時候爆裂
A:請將氣球用手扶住,慢慢安裝入插槽,再用雙手扣進卡扣
0 Comments

    Author

    Ez lin
    Location:

    TAIWAN

    Archives

    August 2018
    June 2018
    November 2017
    September 2017
    July 2017
    June 2017

    Categories

    All

    RSS Feed

LICENSE AGREEMENT
​

Privacy Policy

Refund Policy

If the product has any flaws, please send a message to the webmaster, you can replace the components free of charge.
Picture
Picture
©2003-2020JSPB